Skip to main content

Vocational Education & Training

UEE33011 Certificate III in Electrical Fitting

2020

Didn't study in Australia? Switch to international student information

Not available to international students.
Download course pack
Overview

UEE33011

Casuarina

Estimated completion time: 4 year/s

The length of time to complete this qualification will depend on the location, study mode and selected units.
Refer to the relevant course information flyer for further information.

CDU Reference
Sector
Vocational Education & Training
Industry groups
UTILITIES
Occupation types
Electrician (General)

This qualification provides competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter, repair electrical equipment and includes electrical wiring work only if that work is associated with assembling, maintaining, terminating or altering the wiring between electrical components within a plant or machinery. An electrical fitter is not authorised to install any electrical wiring systems within an electrical installation as prescribed by definitions contained in AS/NZS 3000.

Electrical equipment means any appliance, article, accessory, wire, fitting, cable, conduit or apparatus that generates, uses, conveys or controls (or that is intended to generate, use, convey or control) electricity above extra low voltage.

This qualification is only available as an Apprenticeship.

Course fees

Based on course nominal hours of between 1040 - 1260 hours, approximate 2020 course fees will be:
VET Tuition Fees: $3,536.00 - $4,284.00
Domestic Full Fees: $17,680.00 - $21,420.00

The following Fees are applicable to this course:

Domestic Students

VET tuition fees

This course is subsidised by the NT Government.
2020: VET Tuition Fees for 2020 will be charged at $3.40 per nominal hour for subsidised training. More detailed Information about 2020 VET Tuition fees for eligible NT residents is available in the VET Student Guide.

Fee for service

In some circumstances this course may be available as fee-for-service. Please contact the relevant team to discuss delivery charges for this program.

Career opportunities

Occupations relevant to this qualification in industry sectors such as Electrical Engineering, Electrotechnology include:

  • Electrician (Special Class)
  • Instrumentation and Control Technician

Credit transfers & pathways

Skills recognition

Recognition of Prior Learning (RPL)
RPL is the acknowledgement of a person's skills and knowledge acquired through previous training, work or life experience, which may be used to grant status or credit in a subject regardless of how and where they were attained, including overseas.
This can include skills from:

  • Previous study excluding courses at another VET/TAFE institution, but including courses at school or college, through adult education classes or training programs at work;
  • Work experience (including both work that is paid and unpaid); and/or
  • Life experience (for example leisure pursuits or voluntary work).

RPL is a form of assessment. It is used to determine whether a person has acquired, through formal or informal learning, the skills and experience consistent with the stated competency standards that comprise a qualification. RPL is not time referenced, so there are no parameters on how or when the skills are acquired. However, the skills that have been acquired through life experience etc., must be current and must match the elements and performance criteria contained in the individual unit.

Students seeking RPL need to indicate this on their enrolment form at the time of enrolment.

For further information please refer to the Applicant's Guide to the Recognition of Prior Learning or contact VET RPL Enquiries on 1800 238 838 or email vet.rpl.enquiries@cdu.edu.au.

Credit Transfer
Charles Darwin University as a Registered Training Organisation recognises the Australian Qualifications Framework qualifications and Statement of Attainments issued by any other Australian Registered Training Organisation.

Students are encouraged to submit any requests for credit from previous studies at the time of enrolment, to ensure they are not enrolling in units they may not need to undertake.
In order to apply for exemption/credit transfer from units completed at another training organisation, you will need to complete an Application for Exemption Form available from any campus, centre, or team, or a copy of the form can be obtained from the web.

Your completed Application for Exemption form together with attached documentary evidence (certified copy of Qualification/Statement of Attainment) to support your request for exemption/credit transfer should be submitted directly to the University either in person or by mail. Requests without documentary evidence will not be processed and will be returned to students. There are no fees attached to Credit Transfers.

Pathways

VET to Higher Education Pathway Mapping for completed Awards in the same field or discipline

 

Entry requirements

CDU Entry Requirements

To gain entry into UEE33011 Certificate III in Electrical Fitting, candidates are required to be apprentices who have entered into a Training Contract with Australian Apprenticeships NT.

Students will need to demonstrate an appropriate level of language, literacy and numeracy skills and knowledge to undertake a course at this level.

  • This is a current, nationally accredited qualification from the UEE11 Electrotechnology Training Package.

  • VET for Secondary Students (VSS)

    Select VSS for more detail about this program.

    Employability skills

    Employability Skills are embedded in the training and assessment of national training package qualifications. Information on the Employability Skills relevant to your qualification can be obtained by visiting this website and keying in the national code for the qualification: training.gov.au

    Location and study mode

    Delivery at all locations is subject to sufficient demand and resources.

    Locations: Casuarina

    Study Mode:On campus
    Some components of this qualification may be available in other modes of delivery and not all modes are available at all locations.

    Subject to demand other locations and modes may become available throughout the year.

Contact details

Electrotechnology (Top End)
Location: Casuarina Campus
Phone: 08 8946 7505
Fax: 08 8946 6711
Email: vet.electro@cdu.edu.au

Course structure

To achieve a Certificate III in Electrical Fitting approximately twenty-three (23) units of competency must be completed. This comprises seventeen  (17) core units (totalling 820 weighting points) and approximately six (6) elective units (totally 240 weighting points) as outlined in the packaging rules and listed below. The electives offered may vary between campuses.

The total nominal hours for the sequence listed below is 1060 (total weighting points 1060).
 

  Module/Unit of Competency

Weighting Points

Hours

CORE UNITS OF COMPETENCY
Competencies marked # have pre-requisite competencies

UEENEEC020B Participate in electrical work and competency development activities 60 20
UEENEEE101A Apply Occupational Health Safety regulations, codes and practices in the workplace 20 20
UEENEEE102A# Fabricate, assemble and dismantle utilities industry components 40 40
UEENEEE104A# Solve problems in d.c. circuits 80 80
UEENEEE105A# Fix and secure electrotechnology equipment 20 20
UEENEEE107A# Use drawings, diagrams, schedules, standards, codes and specifications 40 40
UEENEEE137A# Document and apply measures to control OHS risks associated with electrotechnology work 20 20
UEENEEG006A# Solve problems in single and three phase low voltage machines 80 80
UEENEEG033A# Solve problems in single and three phase low voltage electrical apparatus and circuits 60 60
UEENEEG063A# Arrange circuits, control and protection for general electrical installations 40 40
UEENEEG101A# Solve problems in electromagnetic devices and related circuits 60 60
UEENEEG102A# Solve problems in low voltage a.c. circuits 80 80
UEENEEG106A# Terminate cables, cords and accessories for low voltage circuits 40 40
UEENEEG108A# Trouble-shoot and repair faults in low voltage electrical apparatus and circuits 40 80
UEENEEG109A# Develop and connect electrical control circuits 80 80
UEENEEG199A# Conduct compliance and functional verification of electrical apparatus and existing circuits 40 40
UEENEEK142A Apply environmental and sustainable procedures in the energy sector 20 20
  Total nominal hours – core units 820 820

ELECTIVE UNITS OF COMPETENCY
A total weighting of 240 weighting points is required with a range of 0 - 60 points from Group A and 180 - 240 from Group B. 
Competencies marked # have pre-requisite competencies.

Group A - Imported and Common Elective Units 
A maximum weighting of 60 may be selected from Group A

 
UEENEEC001B Maintain documentation 20 20
UEENEEC002B Source and purchase material/parts for installation or service jobs 20 20
UEENEEC003B Provide quotations for installation or service jobs 20 20
UEENEED101A# Use computer applications relevant to a workplace 20 20
Group B - Elective Units 
A maximum weighting of 240 may be selected from Group B
(e.g. all elective units may be selected from this group)
 
UEENEEA110A Assemble, mount and connect control gear and switchgear 40 120
UEENEEA113A# Mount and wire control panel equipment 40 60
UEENEEF102A# Install and maintain cabling for multiple access to telecommunication services 120 120
UEENEEH102A Repair basic electronic apparatus by replacement of components 40 40
UEENEEI101A# Use instrumentation drawings, specifications, standards and equipment manuals 40 40
UEENEEI102A# Solve problems in pressure measurement components and systems 40 40
UEENEEI150A# Develop, enter and verify discrete control programs for programmable controllers 60 60
  Total maximum weighting points – elective units 240

 

  Total maximum weighting points for the qualification 1060

 

 

 

Everything you need to know to get started

How to apply for domestic students

CDU VET has several pathways for you to apply.

 

Visit How to apply for CDU VET courses for more information.

 

Admission requirements for domestic students

Before applying, you may want to check if you meet the admission requirements for studying with CDU.

 

CDU has many pathways to study, so don't worry if you don't meet the admission requirements right now. There is a study pathway to get you started on your journey.

Not sure if you are a domestic or international student?

That's OK - it can be a little tricky to know the difference.

 

To help you out, we've put together a guide to answer any questions you might have.

Are you applying as an International Student?

Everything you need to get apply

How to apply for international students

Applications to CDU must be submitted online.

 

The process is simple, all you need is a valid email address to create your online account.

 

Once you have started the application you will have the option of saving your application and resuming it at a later date.

 

There is no application fee when you apply online.

Find a CDU agent partner

Applicants may seek further information about international education in Australia from the Australian Government Department of Education and Training or from our overseas / external representatives.

 

To help with the process, we've compile a list of authorised representatives.

Not sure if you are a domestic or international student?

That's OK - it can be a little tricky to know the difference.

 

To help you out, we've put together a guide to answer any questions you might have.

 

Things like the difference between domestic and international students or the difference between course types like VET and undergraduate.

Are you applying as a Domestic Student?